A&P oral questions / General
Weight and Balance: A&P oral exam questions
8 practice questions with answers for the Weight and Balance subject (AM.I.C) of the FAA Aviation Mechanic General oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
In weight and balance work, what is the datum, and who decides where it is?
What the examiner listens for
- An imaginary vertical plane from which all horizontal measurements are taken
- Its location is chosen by the manufacturerbonus
- Its location is given in the Type Certificate Data Sheet or Aircraft Specificationsbonus
A good answer: The datum is an imaginary vertical plane from which all horizontal measurements are taken for balance purposes, with the aircraft level. The manufacturer chooses it, and its location is given in the Type Certificate Data Sheet or Aircraft Specifications.
Likely follow-up: Name a couple of typical places a manufacturer puts the datum.
Reference: FAA-H-8083-30B Ch. 6, Datum
What is the main purpose of weighing an aircraft?
What the examiner listens for
- To find its empty weight
- To find where it balances when empty, the empty weight center of gravity
- All later loading and alteration calculations start from those two valuesbonus
A good answer: The main reason to weigh an aircraft is to find its empty weight and its empty weight center of gravity. Every other weight and balance calculation, such as loading or an equipment change, starts from those numbers.
Likely follow-up: Where is that empty weight and empty weight CG information recorded?
Reference: FAA-H-8083-30B Ch. 6, Procedures for Weighing an Aircraft
How do you handle the fuel when preparing to weigh an aircraft, and what fuel condition must you avoid?
What the examiner listens for
- Weigh with fuel drained so only residual, unusable fuel remains, or with tanks completely fullbonus
- Never weigh with partially full tanks
- With partial tanks you cannot determine exactly how much fuel to account forbonus
A good answer: Only residual or unusable fuel belongs in the empty weight, so I either drain the tanks as the manufacturer specifies or weigh with the tanks completely full and subtract the usable fuel mathematically. I never weigh with partially full tanks, because the amount of fuel on board cannot be determined exactly.
Likely follow-up: If you weigh with full tanks, how can you find the actual weight per gallon of the fuel?
Reference: FAA-H-8083-30B Ch. 6, Preparing an Aircraft for Weighing, Fuel System
What does the maximum weight of an aircraft mean, and where is it published?
What the examiner listens for
- It is the maximum authorized weight of the aircraft and its contents
- It is found in the Type Certificate Data Sheet or Aircraft Specifications
- It can differ by category of operation, such as normal versus utilitybonus
A good answer: Maximum weight is the maximum authorized weight of the aircraft and everything in it. It is given in the Type Certificate Data Sheet or Aircraft Specifications, and it may vary with the category the aircraft is operated in.
Likely follow-up: What is the difference between maximum ramp weight and maximum takeoff weight?
Reference: FAA-H-8083-30B Ch. 6, Maximum Weight
In an adverse-loading check on a piston airplane, what is minimum fuel and how do you figure it in pounds?
What the examiner listens for
- Fuel for about one half hour of operation at maximum continuous powerbonus
- In pounds it is the METO horsepower divided by two
A good answer: Minimum fuel is the small amount used for balance calculations, no more than what is needed for half an hour at rated maximum continuous power. In pounds you take the METO horsepower and divide by two.
Likely follow-up: Where would you get the minimum fuel figure for a turbine-powered aircraft?
Reference: FAA-H-8083-30B Ch. 6, Adverse-Loaded CG Checks
How should permanent ballast be installed and identified?
What the examiner listens for
- Attached rigidly to structure so it cannot come loose in flight or a rough landing
- It must not interfere with any control actionbonus
- Usually lead blocks painted red and marked Permanent Ballast, Do Not Removebonus
A good answer: Permanent ballast is attached rigidly to the structure so it cannot be dislodged by maneuvers or a rough landing, and where it cannot interfere with the controls. It is usually lead painted red and marked Permanent Ballast, Do Not Remove.
Likely follow-up: What does installing permanent ballast do to the empty weight and useful load?
Reference: FAA-H-8083-30B Ch. 6, Permanent Ballast
Someone has to stay in the cockpit while the aircraft is being jacked. What is the rule for that person, and how must the jacks be positioned before lifting?
What the examiner listens for
- The person in the aircraft must not move around
- Jacks must be straight under the jack pads before raisingbonus
A good answer: Anyone who has to be in the aircraft during jacking must stay still, because movement shifts the weight and can make the aircraft slip. Before lifting, each jack must be straight under its jack pad.
Likely follow-up: What is the particular hazard of jacking an airplane with spring steel landing gear at the wheel?
Reference: FAA-H-8083-30B Ch. 6, Safety Considerations
With the wheels sitting on platform scales, should the brakes be set or released while you take the readings, and why?
What the examiner listens for
- The brakes should be released
- Set brakes can put side loads on the scalesbonus
- Side loads cause incorrect readings
A good answer: The brakes are released while readings are taken. With the brakes set, side loads can be placed on the scales and give incorrect readings; chocks are used to hold the aircraft instead.
Likely follow-up: If you use chocks on the scales, how do you treat their weight?
Reference: FAA-H-8083-30B Ch. 6, Weighing Points
These are 8 of the 34 questions MockDME has for this subject. The other 26 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.