A&P oral questions / Powerplant
Turbine Engine Air Systems: A&P oral exam questions
4 practice questions with answers for the Turbine Engine Air Systems subject (AM.III.K) of the FAA Aviation Mechanic Powerplant oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
A piston engine is cooled by air over its cylinder fins. How is a gas turbine engine cooled?
What the examiner listens for
- Mostly by air passing through the inside of the engine
- Far more air is taken in than is needed for combustion, and the surplus cools the hot sectionbonus
- Outside or fan air also cools the engine case and nacellebonus
A good answer: Because combustion is continuous, nearly all the cooling air has to pass through the inside of the engine. Much more air is admitted than is needed to burn the fuel, and that surplus air cools the hot section to acceptable temperatures, while fan or outside air cools the case and nacelle.
Likely follow-up: Which area of the engine exterior runs hottest?
Reference: FAA-H-8083-32B Ch. 6, Turbine Engine Cooling
What is used to cool the turbine discs, vanes, and blades, and where does it come from?
What the examiner listens for
- Compressor bleed air, called secondary or internal airflow
- It is taken from a compressor stage with enough pressure but before the air gets too hotbonus
- It can also help cool the turbine bearingbonus
A good answer: They are cooled by bleed air from the compressor, routed internally through the engine. It is bled from a stage where the air has enough pressure but is not yet too warm, and it can also be used to help cool the turbine bearing.
Likely follow-up: After the cooling air has done its job, where does it go?
Reference: FAA-H-8083-32B Ch. 6, Turbine Engine Lubrication Systems
What is the job of the air inlet duct on a turbine engine, and what can happen if the airflow it delivers is disturbed?
What the examiner listens for
- Deliver smooth, distortion-free air in the required quantity to the compressor
- Disturbed or uneven airflow can cause compressor stall
- It can also cause excessive turbine temperaturesbonus
A good answer: The inlet has to deliver a uniform, distortion-free flow of air in the required quantity to the compressor. If the flow is turbulent or uneven, for example from a damaged or iced inlet, the compressor can stall and turbine temperatures can go too high.
Likely follow-up: Is the inlet duct normally considered part of the engine or part of the airframe?
Reference: FAA-H-8083-32B Ch. 3, Turbine Engine Inlet Systems
You have replaced a section of hot bleed air ducting. What is the risk if a joint is not sealed properly, and how do you verify your work?
What the examiner listens for
- A bad joint lets hot, high-pressure bleed air escape into the surrounding area
- Leak check or pressure test the duct as the maintenance manual specifies
- Make sure the seal is seated evenly and the clamps are securebonus
- Let the system cool and depressurize before opening itbonus
A good answer: A poor joint lets very hot, high-pressure air leak out, where it can overheat nearby structure, wiring, and components. I make sure the seal bears evenly and the clamps are tight, then leak check or pressure test the duct at the pressure the manual gives. Before opening a bleed system I also make sure it is depressurized and cool.
Likely follow-up: How can you find a bleed duct leak that you cannot hear?
Reference: FAA-H-8083-31B Ch. 15, Thermal Pneumatic Anti-icing (ducting)
These are 4 of the 13 questions MockDME has for this subject. The other 9 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.