A&P oral questions / Airframe
Rotorcraft Fundamentals: A&P oral exam questions
8 practice questions with answers for the Rotorcraft Fundamentals subject (AM.II.N) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
What is torque reaction on a single-rotor helicopter, and what counteracts it?
What the examiner listens for
- The fuselage tends to rotate opposite to the main rotor
- It is counteracted by the tail rotor, or antitorque rotor
- Torque increases with engine powerbonus
A good answer: As the engine turns the main rotor one way, the fuselage tends to rotate the opposite way; that is torque. On a single-rotor helicopter the tail rotor produces thrust to counteract it.
Likely follow-up: Why is there no torque reaction during autorotation?
Reference: FAA-H-8083-31B Ch. 2, Torque Compensation
What does the collective pitch control do?
What the examiner listens for
- It changes the pitch angle of all main rotor blades at the same time and by the same amount
- Raising it increases blade pitch and liftbonus
A good answer: The collective changes the pitch angle of all the main rotor blades simultaneously and equally. Raising it increases pitch and lift; lowering it decreases them.
Likely follow-up: What keeps rotor rpm constant when the collective is raised?
Reference: FAA-H-8083-31B Ch. 2, Collective Pitch Control
What does a helicopter transmission system do, and what are its main components?
What the examiner listens for
- It transfers engine power to the main rotor, tail rotor and accessories
- Main components: main rotor transmission, tail rotor drive, clutch, freewheeling unitbonus
A good answer: The transmission system transfers power from the engine to the main rotor, the tail rotor and accessories. Its main parts are the main rotor transmission, the tail rotor drive system, the clutch and the freewheeling unit.
Likely follow-up: How is the oil level in a main transmission normally checked?
Reference: FAA-H-8083-31B Ch. 2, Transmission System
After rigging a helicopter's flight controls, what do you verify about the main rotor blades?
What the examiner listens for
- Names at least one of: maximum and minimum blade pitch angles within limits; blade tracking correct
- Tabs on the main rotor blades, where provided, are correctly setbonus
- Control travel and neutral positions are correctbonus
A good answer: Check that the maximum and minimum pitch angles of the main rotor blades are within the specified limits, for collective and for fore-and-aft and lateral cyclic, and that the blades track correctly.
Likely follow-up: What do you check on the tail rotor after rigging?
Reference: FAA-H-8083-31B Ch. 2, Helicopter rigging
What is the function of the main rotor, and what are its main parts?
What the examiner listens for
- It is the rotating part of the helicopter that generates lift
- It consists of a mast, a hub and the rotor bladesbonus
A good answer: The rotor system is the rotating part of the helicopter that generates lift. It consists of the mast, driven by the transmission, the hub on top of the mast, and the blades attached to the hub.
Likely follow-up: What are modern main rotor blades usually made of?
Reference: FAA-H-8083-31B Ch. 1, Main Rotor System
A pilot reports a low-frequency, one-per-revolution vibration. Where does it come from?
What the examiner listens for
- The main rotor itself
- One blade is producing more lift than another, or the rotor is out of track or balancebonus
A good answer: Low-frequency vibrations, one or two per rev, come from the main rotor itself. A one-per-rev is caused by one blade developing more lift than another at the same point, so you check track and balance.
Likely follow-up: What would you suspect if the vibration were high frequency instead?
Reference: FAA-H-8083-31B Ch. 2, Low Frequency Vibration
Why must you never approach a single-rotor helicopter from the rear while it is running?
What the examiner listens for
- The spinning tail rotor is invisible
- Approach from where the pilot can see youbonus
- Go around the nose, never around the tailbonus
A good answer: Because the tail rotor is invisible when it is turning. You approach in view of the pilot, and if you have to change sides you go around the nose, never around the tail.
Likely follow-up: What should you avoid carrying when you walk under turning main rotor blades?
Reference: FAA-H-8083-30B Ch. 1, Safety Around Helicopters
A helicopter needs a ground run to check tail rotor track after maintenance. Who may do the run-up?
What the examiner listens for
- Only authorized personnel
- The engine is started in accordance with the applicable maintenance manualbonus
A good answer: A ground run-up is performed only by authorized personnel, and the engine is started and run according to the applicable maintenance manual.
Likely follow-up: What hazards would you brief the people standing nearby about?
Reference: FAA-H-8083-31B Ch. 2, Tail Rotor Tracking
These are 8 of the 32 questions MockDME has for this subject. The other 24 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.