A&P oral questions / Powerplant
Reciprocating Engines: A&P oral exam questions
5 practice questions with answers for the Reciprocating Engines subject (AM.III.A) of the FAA Aviation Mechanic Powerplant oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
What are the common ways reciprocating aircraft engines are classified, and which types do you know?
What the examiner listens for
- Classified by cylinder arrangement
- Arrangements are inline, V-type, radial, and opposedbonus
- Also classified by cooling method: air cooled or liquid cooledbonus
A good answer: Reciprocating engines are classified by cylinder arrangement, which means inline, V-type, radial, or opposed, and by cooling method, either air cooled or liquid cooled.
Likely follow-up: Why is the horizontally opposed engine so widely used on light aircraft?
Reference: FAA-H-8083-32B Ch. 1, Types of Engines
On a horizontally opposed engine, what operates the valves, and how fast does it turn compared to the crankshaft?
What the examiner listens for
- A camshaft operates the valves
- The camshaft turns at one-half crankshaft speed
- It is gear driven from the crankshaftbonus
- Motion goes through tappet, push rod, and rocker arm to the valvebonus
A good answer: The valves are operated by a camshaft that is gear driven from the crankshaft and always turns at one-half crankshaft speed. The cam lobes lift the tappets, which act through the push rods and rocker arms to open the valves.
Likely follow-up: Why does the camshaft have to turn at half crankshaft speed on a four-stroke engine?
Reference: FAA-H-8083-32B Ch. 1, Camshaft
After the cylinders of an engine have been sprayed with preservative for storage, why must the crankshaft not be turned?
What the examiner listens for
- Turning breaks the seal of preservative between pistons and cylinder walls
- The protective coating is scraped off the cylinder walls, exposing bare metal to corrosionbonus
- The engine should be tagged: do not turn crankshaft, engine preservedbonus
A good answer: Turning the crankshaft breaks the seal of corrosion-preventive mixture between the pistons and cylinder walls and scrapes the coating off the walls, letting air in and exposing bare metal to corrosion. The engine should carry a tag saying not to turn the crankshaft.
Likely follow-up: What else is sealed or treated when an engine is prepared for storage?
Reference: FAA-H-8083-32B Ch. 8, Engine Preservation & Return to Service
During the magneto check on a ground run, you switch from both to one magneto and see no rpm drop at all. What does that indicate?
What the examiner listens for
- A faulty ground on one side of the ignition system, the magneto is not being switched off
- That magneto stays hot and could fire if the propeller is turnedbonus
- A slight drop in rpm is the normal indicationbonus
A good answer: No drop means the other magneto is probably not being grounded out, so there is a faulty ground connection, a bad P-lead or switch. That is a safety problem because the magneto is still hot with the switch off and the engine could fire if the propeller is moved.
Likely follow-up: What does a fast rpm drop on one magneto usually point to, compared with a slow drop?
Reference: FAA-H-8083-32B Ch. 10, Ground Check
Before starting a radial engine that has been sitting, how do you check for hydraulic lock, and what do you do if you find one?
What the examiner listens for
- With ignition off, pull the propeller through several revolutions by hand
- Never force the propeller if it stops or is hard to turn
- Remove a spark plug from the lower cylinders and pull through to drain the liquidbonus
- Never turn the propeller backward to clear itbonus
A good answer: With the ignition off, pull the propeller through three or four revolutions by hand. If it stops or takes abnormal effort, do not force it, because that can bend or break a connecting rod. Remove a spark plug from the lower cylinders and pull the prop through in the normal direction to expel the liquid.
Likely follow-up: Why should you not clear a hydraulic lock by turning the propeller backward?
Reference: FAA-H-8083-30B Ch. 1, Reciprocating Engines (engine starting)
These are 5 of the 20 questions MockDME has for this subject. The other 15 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.