A&P oral questions / Powerplant

Reciprocating Engine Induction and Cooling Systems: A&P oral exam questions

5 practice questions with answers for the Reciprocating Engine Induction and Cooling Systems subject (AM.III.J) of the FAA Aviation Mechanic Powerplant oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.III.J.K1 · Knowledge · Reciprocating engine induction and cooling system theory, components, and operation

On a reciprocating engine, what controls how much air flows into the engine, and what do we call the pressure downstream of it?

What the examiner listens for
  • The throttle plate controls the amount of air flowing to the engine
  • The pressure after the throttle is manifold pressure
  • Manifold pressure is measured in inches of mercurybonus
  • Manifold pressure is an indication of engine power outputbonus

A good answer: The throttle plate in the carburetor or fuel injection unit controls the airflow. The pressure of the air coming out of the throttle is manifold pressure, measured in inches of mercury, and it reflects engine power output.

Likely follow-up: Why is a balance tube installed between the two sides of an updraft induction system?

Reference: FAA-H-8083-32B Ch. 3, Reciprocating Engine Induction Systems

AM.III.J.K3 · Knowledge · Superchargers and controls

What is the difference between an internally driven supercharger and a turbocharger in terms of what each one compresses?

What the examiner listens for
  • An internally driven supercharger compresses the air-fuel mixture after it leaves the carburetor
  • A turbocharger compresses the air before it is mixed with fuel
  • The internal supercharger is driven mechanically by the enginebonus
  • The turbocharger is driven by exhaust gasbonus

A good answer: An internally driven supercharger is gear driven by the engine and compresses the air-fuel mixture after it leaves the carburetor. A turbocharger is driven by exhaust gas and compresses the air before fuel is added.

Likely follow-up: Why does a supercharged induction system need temperature sensing as well as pressure sensing?

Reference: FAA-H-8083-32B Ch. 3, Supercharged Induction Systems

AM.III.J.K5 · Knowledge · Augmenter cooling system

How does an augmenter cooling system pull cooling air over the engine?

What the examiner listens for
  • Exhaust gas is discharged into the augmenter tubes
  • The exhaust flow creates a low-pressure area in the tubesbonus
  • That low pressure draws additional cooling air over the engine
  • Cooling does not depend entirely on prop washbonus

A good answer: The exhaust is fed into augmenter tubes, where its velocity creates a low-pressure, venturi-type effect. That draws additional cooling air over the engine, so cooling is not entirely dependent on prop wash.

Likely follow-up: What are the vanes in the augmenter tubes used for?

Reference: FAA-H-8083-32B Ch. 6, Reciprocating Engine Cooling Systems

AM.III.J.K8 · Knowledge · Pressure cowling air flow and control

In a pressure-cooled cowling, what makes the cooling air flow down through the cylinder fins?

What the examiner listens for
  • Ram air builds a high-pressure area above the cylindersbonus
  • The cowl outlet at the bottom rear creates a low-pressure areabonus
  • The pressure difference forces air past the cylinders
  • Cowl flaps change the exit area to control the airflowbonus

A good answer: Ram air piles up on top of the engine and creates high pressure, while the outlet at the bottom rear of the cowl is a low-pressure area. That pressure differential forces the air down past the cylinders through the baffles and deflectors.

Likely follow-up: What happens to cooling airflow and engine temperature when the cowl flaps are closed?

Reference: FAA-H-8083-32B Ch. 6, Cylinder Baffle & Deflector System Inspection

AM.III.J.R1 · Risk management · Maintenance on turbochargers

Why does the exhaust system on a turbocharged engine call for extra care during inspection and maintenance?

What the examiner listens for
  • It operates at much higher pressure and temperaturebonus
  • Any leak lets exhaust escape with torch-like intensity
  • The escaping gas can severely damage adjacent structurebonus
  • Exhaust leaks also reduce turbocharger performancebonus

A good answer: With a turbocharger the exhaust system runs at greatly increased pressure and temperature, so even a small leak escapes like a torch and can severely damage nearby structure. Every joint and component ahead of the turbine has to be inspected carefully for leaks and cracks.

Likely follow-up: How would an exhaust leak ahead of the turbine show up in engine performance?

Reference: FAA-H-8083-32B Ch. 3, Exhaust Systems with Turbocharger

These are 5 of the 20 questions MockDME has for this subject. The other 15 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects