A&P oral questions / Airframe
Non-Metallic Structures: A&P oral exam questions
8 practice questions with answers for the Non-Metallic Structures subject (AM.II.B) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
Before you inspect a wood aircraft structure, what condition must the aircraft be in, and why?
What the examiner listens for
- The aircraft and its wood must be dry
- Damp wood swells and hides the true condition of the glue jointsbonus
- Open the inspection covers in a dry, ventilated hangarbonus
- A moisture meter can confirm the moisture contentbonus
A good answer: The aircraft must be dry. Wet or damp wood swells, which makes it hard to judge the glue joints, so you put it in a dry, ventilated hangar with panels open and check with a moisture meter if in doubt.
Likely follow-up: What moisture content is ideal, and above what reading does fungus become a concern?
Reference: FAA-H-8083-31B Ch. 6, Inspection of Wood Structures
You are selecting wood for a repair and suspect a board contains compression wood. What do you do with it?
What the examiner listens for
- Reject it
- Compression wood is very detrimental to strengthbonus
- It is hard to recognizebonus
A good answer: Reject it. Compression wood is very detrimental to strength and hard to recognize, so if there is any doubt the material is rejected.
Likely follow-up: How is a compression failure different from compression wood?
Reference: FAA-H-8083-31B Ch. 6, Defects Not Permitted
In which direction should fabric seams preferably run on a covered surface?
What the examiner listens for
- Parallel to the line of flight
- Spanwise seams are acceptablebonus
A good answer: Seams parallel to the line of flight are preferred, although spanwise seams are acceptable.
Likely follow-up: Why are thick sewn seams avoided on the leading edge of a thin airfoil?
Reference: FAA-H-8083-31B Ch. 3, Fabric Seams
The dope finish on a fabric airplane is cracked but the fabric itself tests airworthy. How can the finish be restored?
What the examiner listens for
- Apply a rejuvenator according to the manufacturer's instructions
- It softens the old dope and adds plasticizers that fill the cracksbonus
- Follow with aluminum-pigmented dope and topcoatsbonus
- Polyurethane finishes cannot be rejuvenatedbonus
A good answer: If the fabric is still strong, the dope can be treated with a rejuvenator, which softens the coating with strong solvents and adds plasticizers that fill the cracks. Then aluminum-pigmented dope and the topcoats are reapplied.
Likely follow-up: What do you do if the fabric under the cracked dope is not airworthy?
Reference: FAA-H-8083-31B Ch. 3, Determining Fabric Condition
In a composite, what is the job of the fibers and what is the job of the matrix?
What the examiner listens for
- Fibers are the primary load-carrying element
- The matrix supports the fibers and bonds them togetherbonus
- The matrix transfers loads to the fibersbonus
A good answer: The fibers carry the load; the composite is only strong and stiff in the direction of the fibers. The matrix, the resin, supports the fibers, bonds them together and transfers the loads to them.
Likely follow-up: Why does ply orientation matter so much when you replace a damaged ply?
Reference: FAA-H-8083-31B Ch. 7, Major Components of a Laminate
When you inspect a windshield, what kind of damage is not acceptable?
What the examiner listens for
- Scratches or other damage that obstructs the pilot's vision
- Some damage may be acceptable near the edges, per the manufacturer's limitsbonus
A good answer: Scratches or any other damage that obstruct the pilot's vision are not acceptable. Some damage may be allowed at the edges of the windshield, depending on the manufacturer's limits.
Likely follow-up: What would you do at the first sign of a crack in a plastic window?
Reference: FAA-H-8083-31B Ch. 7, Optical Considerations
During an annual or 100-hour inspection, what are you required to look for on seats and safety belts?
What the examiner listens for
- Poor condition or apparent defects of the seats and belts
- Apparent defects, such as frayed webbing or faulty buckles and attachmentsbonus
A good answer: Part 43 Appendix D requires seats and safety belts to be inspected for poor condition and apparent defects. In practice that means webbing, stitching, buckles and attachments.
Likely follow-up: Is replacing a safety belt a job an owner may do as preventive maintenance?
Reference: 14 CFR part 43, Appendix D (c)(2)
How do you protect your skin when handling resins and damaged composite parts?
What the examiner listens for
- Wear approved gloves and protective clothing
- Chemicals can burn or irritate the skinbonus
- Broken fibers can penetrate and lodge in the skinbonus
- Wash hands before eatingbonus
A good answer: Wear approved gloves and protective clothing, because resins and solvents can burn sensitive skin and single fibers from damaged parts can penetrate and lodge in the skin. Wash your hands before eating or using the toilet.
Likely follow-up: Why must the gloves be an approved type and not just any glove?
Reference: FAA-H-8083-31B Ch. 7, Skin Protection
These are 8 of the 67 questions MockDME has for this subject. The other 59 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.