A&P oral questions / Airframe

Metallic Structures: A&P oral exam questions

8 practice questions with answers for the Metallic Structures subject (AM.II.A) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.II.A.K1 · Knowledge · Inspection/testing of metal structures

During a structural inspection, how could you tell that a rivet is working even though you cannot see it move?

What the examiner listens for
  • Names at least one of: dark, greasy residue around the rivet head, or deteriorated paint or primer around it
  • A working rivet moves under structural stressbonus

A good answer: A working rivet moves under load but not enough to see. You spot it by a dark, greasy residue, or by deteriorated paint and primer, around the rivet head.

Likely follow-up: If you found a group of rivets like that, what would you inspect next?

Reference: FAA-H-8083-31B Ch. 4, Inspection of Damage

AM.II.A.K4 · Knowledge · Layout, forming, and drilling of sheet metal components

When you lay out a bend in aluminum sheet, how should the bend line run in relation to the grain of the metal?

What the examiner listens for
  • The bend line should lie at 90 degrees to the grain, if possible
  • Bending across the grain reduces the chance of crackingbonus

A good answer: Whenever possible the bend line should be laid out at 90 degrees to the grain of the metal, that is, across the grain.

Likely follow-up: What would you do if the sheet starts to crack while you are cold forming a small radius?

Reference: FAA-H-8083-31B Ch. 4, Forming Operations & Terms

AM.II.A.K6 · Knowledge · Heat treatment processes for aluminum

Some rivets, such as 2024 DD rivets, are called ice box rivets. Why are they kept in a freezer?

What the examiner listens for
  • They are too hard to drive as received, so they are heat treated soft firstbonus
  • Cold storage retards hardening
  • They are taken out just before usebonus

A good answer: DD rivets are too hard to drive as received, so they are heat treated to soften them and then stored in a freezer, which slows the hardening. They are removed just before driving.

Likely follow-up: Which rivet can be driven as received and is the most common repair rivet?

Reference: FAA-H-8083-31B Ch. 4, Solid Shank Rivet

AM.II.A.K8 · Knowledge · Rivet removal and installation methods

Walk me through removing a solid universal head rivet without damaging the hole.

What the examiner listens for
  • Drill into the manufactured head with a bit slightly smaller than the shank
  • Drill only to the depth of the head
  • Break the head off with a punchbonus
  • Drive the shank out with a punch while supporting the sheetbonus

A good answer: File a flat and center punch the manufactured head, drill to the depth of the head with a bit one size smaller than the shank, snap the head off with a punch, then drive the shank out with a punch while backing up the sheet.

Likely follow-up: What happens if you drill too deep?

Reference: FAA-H-8083-31B Ch. 4, Removal of Rivets

AM.II.A.K11 · Knowledge · Storage/handling of welding gases

In what position are welding gas cylinders stored and moved, and why is that especially important for acetylene?

What the examiner listens for
  • Upright
  • Acetylene cylinders contain liquid acetone that could enter the regulator and hosesbonus
  • Cylinders are secured, for example with a chainbonus
  • Protective cap stays on until the cylinder is put in servicebonus

A good answer: Cylinders are stored and transported upright and secured. An acetylene cylinder contains acetone, and on its side the acetone can get into the regulator, hose and torch and lead to a flashback.

Likely follow-up: If an acetylene cylinder has been lying on its side, what do you do before using it?

Reference: FAA-H-8083-31B Ch. 5, Gas Cylinders

AM.II.A.K14 · Knowledge · Purpose and types of shielding gases

What is the purpose of the shielding gas in TIG or MIG welding, and which gases are commonly used?

What the examiner listens for
  • It keeps oxygen in the air away from the arc and molten puddle
  • It prevents oxides forming in the weldbonus
  • Names argon or helium (either one is enough)

A good answer: The shielding gas surrounds the arc and puddle to keep air out so oxides do not form in the weld. Argon and helium are the usual inert gases.

Likely follow-up: For manual TIG welding of aluminum, which gas is preferred, and why?

Reference: FAA-H-8083-31B Ch. 5, Gas Tungsten Arc Welding (GTAW)

AM.II.A.K17 · Knowledge · Types of structures and their characteristics

In a true monocoque fuselage, what carries the primary loads?

What the examiner listens for
  • The skin carries the primary stresses
  • Formers and bulkheads only give the shapebonus
  • Its main problem is keeping enough strength within weight limitsbonus

A good answer: In true monocoque construction the skin carries the primary stresses and keeps the fuselage rigid; formers, frames and bulkheads only give it shape.

Likely follow-up: How does semimonocoque construction improve on that?

Reference: FAA-H-8083-31B Ch. 1, Monocoque Type

AM.II.A.R2 · Risk management · Utilizing maintenance safety practices/precautions for sheet metal structures

You need to drill sheet metal close to flammable materials. Which type of drill motor is recommended, and why?

What the examiner listens for
  • A pneumatic drill motor
  • An electric drill can produce sparks that are a fire or explosion hazardbonus

A good answer: Use a pneumatic drill motor, because the sparks from an electric drill motor could ignite the flammable material.

Likely follow-up: What other precautions would you take before drilling near a fuel tank?

Reference: FAA-H-8083-31B Ch. 4, Portable Power Drills

These are 8 of the 46 questions MockDME has for this subject. The other 38 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects