A&P oral questions / Airframe

Landing Gear Systems: A&P oral exam questions

8 practice questions with answers for the Landing Gear Systems subject (AM.II.E) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.II.E.K1 · Knowledge · Fixed and retractable landing gear systems

What is the main reason for making landing gear retractable instead of fixed?

What the examiner listens for
  • Retracted gear is out of the slipstream, so parasite drag is reduced
  • Fixed gear stays exposed to the airflow in flightbonus
  • Most retraction systems are hydraulically operatedbonus

A good answer: Retractable gear stows in the fuselage or wing in flight, so it is out of the slipstream and does not cause parasite drag. Fixed gear stays exposed, which is acceptable on slower light aircraft.

Likely follow-up: What power source operates most retractable landing gear?

Reference: FAA-H-8083-31B Ch. 13, Fixed & Retractable Landing Gear

AM.II.E.K3 · Knowledge · Landing gear strut servicing/lubrication

To check the fluid level in most air-oil shock struts, what condition does the strut have to be in?

What the examiner listens for
  • Deflated, with the air pressure released
  • Fully compressed
  • Follow the manufacturer's servicing instructionsbonus

A good answer: Most struts must be deflated and fully compressed to check the fluid level, and then filled to the level of the service valve port, following the manufacturer's instructions.

Likely follow-up: With the strut compressed, to what level do you fill it with fluid?

Reference: FAA-H-8083-31B Ch. 13, Shock Strut Operation

AM.II.E.K5 · Knowledge · Steering systems

What is a shimmy damper for, and how does the typical one work?

What the examiner listens for
  • It controls rapid oscillation, or shimmy, of the nose wheel
  • It works by hydraulic dampingbonus
  • It is usually an external unit between the upper and lower strutbonus

A good answer: A shimmy damper controls the tendency of the nose gear to oscillate rapidly at certain speeds. The typical unit does this through hydraulic damping and is mounted between the upper and lower shock strut.

Likely follow-up: Why are the torque links alone not enough to stop shimmy?

Reference: FAA-H-8083-31B Ch. 13, Shimmy Dampers

AM.II.E.K7 · Knowledge · Brake assembly servicing and inspection

How can you check brake lining wear while the brake is still installed on the aircraft?

What the examiner listens for
  • Names at least one of: measuring a wear indicator pin, the exposed lining, or the disc-to-housing distance, depending on the brake
  • Compare the measurement with the manufacturer's limitsbonus
  • Some measurements are taken with the brakes appliedbonus

A good answer: Use the method the manufacturer gives for that brake: many have a wear indicator pin whose exposed length shows lining wear, others are measured at the lining itself or between the disc and the housing with brakes applied. Compare with the manual limits.

Likely follow-up: On a brake with a wear pin, what happens to the exposed pin length as the linings wear?

Reference: FAA-H-8083-31B Ch. 13, Lining Wear

AM.II.E.K9 · Knowledge · Wheel, brake, and tire construction

What is the purpose of the fusible plugs, or thermal plugs, in a wheel?

What the examiner listens for
  • The core melts when the wheel gets dangerously hot
  • It releases the tire pressure before the tire or wheel can explode

A good answer: A fusible plug has a core that melts at a lower temperature than the rest of the plug. If heavy braking overheats the wheel, the core melts and releases the air from the tire before it can explode.

Likely follow-up: If you find one fusible plug with a deformed core, what do you do?

Reference: FAA-H-8083-31B Ch. 13, Fusible Plug Inspection

AM.II.E.K10 · Knowledge · Tire storage, care, and servicing

Why is an underinflated aircraft tire dangerous?

What the examiner listens for
  • It flexes beyond its design limits
  • The excess flexing builds up heat that weakens the tire carcass
  • The internal damage may not be visiblebonus

A good answer: An underinflated tire flexes beyond its design limits. That causes excessive heat build-up, which weakens the carcass and can lead to tire failure, often with damage you cannot see.

Likely follow-up: How often should tire pressure be checked?

Reference: FAA-H-8083-31B Ch. 13, Inflation

AM.II.E.K13 · Knowledge · Alternative landing gear systems (e.g., skis, floats)

Why do floats need frequent inspection, and what is the main thing you are looking for?

What the examiner listens for
  • Corrosion of metal parts
  • Corrosion develops rapidly, particularly in salt water operationbonus
  • Also damage from collisions or hard landingsbonus

A good answer: Floats need periodic and frequent inspection mainly for corrosion, because metal parts corrode rapidly, especially when the aircraft operates in salt water. Also look for damage from collisions and hard landings.

Likely follow-up: How is a float tested for leaks after a hull repair?

Reference: AC 43.13-1B, para 9-9

AM.II.E.R2 · Risk management · Use of aircraft jacks

What is the purpose of the safety collar, or locking collar, on an aircraft jack?

What the examiner listens for
  • It mechanically holds the load if the jack loses hydraulic pressure
  • It is kept screwed down against the jack cylinder as the jack is raisedbonus

A good answer: The safety collar is kept screwed down against the jack cylinder as the jack is raised, so that if the jack loses hydraulic pressure the aircraft does not drop or tilt.

Likely follow-up: On some aircraft, what must be installed before using wing jacks to spread the load?

Reference: FAA-H-8083-30B Ch. 6, Jacking the Aircraft

These are 8 of the 44 questions MockDME has for this subject. The other 36 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects