A&P oral questions / General
Inspection Concepts and Techniques: A&P oral exam questions
7 practice questions with answers for the Inspection Concepts and Techniques subject (AM.I.K) of the FAA Aviation Mechanic General oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
How fine a measurement can you read on a standard micrometer, and what does a vernier scale on the barrel add?
What the examiner listens for
- Each thimble graduation is one thousandth of an inch
- The vernier scale reads to one ten-thousandth of an inch
A good answer: A standard micrometer reads to one thousandth of an inch on the thimble. A vernier scale divides each thousandth into ten parts, so you can read to one ten-thousandth.
Likely follow-up: How far does the spindle move with one full turn of the thimble?
Reference: FAA-H-8083-30B Ch. 11, Vernier Scale
How often should a torque wrench be calibrated, and what would make you send it for calibration early?
What the examiner listens for
- At regular scheduled intervals, at least about once a year
- Immediately after it has been dropped or abused
A good answer: Torque wrenches are calibrated on a regular schedule; AC 43.13 says at least once a year, and some manufacturers call for six months. It is rechecked immediately if it has been dropped or abused.
Likely follow-up: Do all torque wrenches have the same recommended calibration interval?
Reference: AC 43.13-1B, para 7-40a
Walk me through the steps of a dye penetrant inspection.
What the examiner listens for
- Clean the surface thoroughly
- Apply the penetrant and allow it time to enterbonus
- Remove the excess penetrant and dry the partbonus
- Apply developer, then inspect
A good answer: Clean the surface thoroughly, apply the penetrant and give it time to soak in, remove the excess penetrant, dry the part, apply the developer, and then inspect and interpret the indications.
Likely follow-up: What happens if you wash too aggressively when removing the excess penetrant?
Reference: FAA-H-8083-30B Ch. 10, Liquid Penetrant Inspection
Which aircraft need a 100-hour inspection, and can the 100 hours ever be exceeded?
What the examiner listens for
- Aircraft carrying persons for hire or used for flight instruction for hire
- May be exceeded by not more than 10 hours to reach a place where the inspection can be done
- The excess time counts toward the next 100 hoursbonus
A good answer: Aircraft that carry people for hire, or are provided for flight instruction for hire, need an inspection every 100 hours. The limit may be exceeded by up to 10 hours en route to where the inspection can be done, and that time counts toward the next 100 hours.
Likely follow-up: If the aircraft flies 6 hours over to get to the shop, when is the next 100-hour due?
Reference: 14 CFR 91.409(b)
How do you do a tap test on a bonded or composite panel, and what tells you there is a problem?
What the examiner listens for
- Lightly tap the surface with a coin or light hammerbonus
- Compare the sound with a known good areabonus
- A flat or dead sound indicates delamination or disbond
A good answer: Tap the surface lightly with a coin or a light tap hammer and compare the ring with a known good area. A flat or dead sound indicates possible delamination or debonding.
Likely follow-up: What is the limitation of tap testing on thick skins or on honeycomb?
Reference: FAA-H-8083-30B Ch. 10, Tap Testing
How can a micrometer be damaged in everyday use so that it gives wrong readings?
What the examiner listens for
- Names at least two of: dropping it, over-tightening the spindle, sliding work between anvil and spindle
- Over-tightening the spindle can spring the frame permanentlybonus
- Sliding work between anvil and spindle wears the facesbonus
A good answer: Dropping it can permanently affect its accuracy, over-tightening the spindle on the work can spring the frame, and dragging work between the anvil and spindle wears the measuring faces.
Likely follow-up: How would you check whether a micrometer is still reading correctly?
Reference: FAA-H-8083-30B Ch. 11, Using a Micrometer
Who decides which NDI method is used on a particular part, and where do you find that requirement?
What the examiner listens for
- The product manufacturer or the FAA specifies the method
- Found in the maintenance or overhaul manual, ADs or service bulletinsbonus
A good answer: The manufacturer or the FAA generally specifies the NDI method and procedure, in the inspection, maintenance or overhaul manual, an airworthiness directive, or a service bulletin.
Likely follow-up: What is the risk of substituting a different NDI method on your own?
Reference: FAA-H-8083-30B Ch. 10, Training, Qualification, & Certification
These are 7 of the 27 questions MockDME has for this subject. The other 20 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.