A&P oral questions / Airframe
Ice and Rain Control Systems: A&P oral exam questions
4 practice questions with answers for the Ice and Rain Control Systems subject (AM.II.L) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
Under what atmospheric conditions should you expect ice to form on an aircraft in flight?
What the examiner listens for
- Visible moisture in the air, such as cloud or rain
- Temperature near or below freezing
- Carburetor ice is an exception that can form in warm weatherbonus
A good answer: Airframe ice can be expected whenever there is visible moisture in the air and the temperature is near or below freezing. Supercooled droplets freeze when the aircraft surface disturbs them. Carburetor icing is the exception; it can occur in warm, humid weather.
Likely follow-up: What is the difference between clear ice and rime ice?
Reference: FAA-H-8083-31B Ch. 15, Icing Effects
On a business jet or transport aircraft, where does the heat for the thermal wing anti-ice system come from, and how does it reach the leading edge?
What the examiner listens for
- Hot bleed air from the engine compressor
- It is routed through ducts and valves to the leading edgebonus
- Perforated ducts or piccolo tubes distribute it along the inside of the leading edgebonus
A good answer: Thermal wing anti-ice on jets uses hot air bled from the engine compressor. Valves and ducting carry it out to the leading edge, where piccolo tubes or perforated ducts spray it against the inside of the skin before it is vented overboard.
Likely follow-up: How would you locate a leak in the wing anti-ice ducting?
Reference: FAA-H-8083-31B Ch. 15, Thermal Pneumatic Anti-icing
Why should a chemical rain repellent system never be operated on a dry windshield, and what do you do if it happens?
What the examiner listens for
- Undiluted repellent on dry glass restricts visibility
- Do not run the wipers, because that increases smearingbonus
- Rinse the residue off with fresh water as soon as possiblebonus
A good answer: On a dry window the heavy, undiluted repellent smears and restricts visibility. If it is sprayed by mistake, do not operate the wipers, since that makes the smearing worse. Rinse the windshield and nearby skin thoroughly with fresh water, because residue can stain or corrode.
Likely follow-up: When you operationally check windshield wipers on the ground, what condition should the glass be in?
Reference: FAA-H-8083-31B Ch. 15, Chemical Rain Repellent
What is the hazard when you check pitot heat on the ground, and how can you confirm it works without touching the tube?
What the examiner listens for
- The pitot tube gets extremely hot and can burn you
- Watch an ammeter or load meter for the current draw when the heater is switched on
- Keep the ground test shortbonus
A good answer: A pitot heater is built to keep ice off at very low temperatures and high speed, so on the ground it becomes extremely hot and can cause a serious burn. The safe way to confirm it works is to watch the ammeter or load meter for a rise in current when it is switched on.
Likely follow-up: Besides pitot tubes, what other probes and sensors are typically protected by electric heat?
Reference: FAA-H-8083-31B Ch. 15, Thermal Electric Anti-Icing
These are 4 of the 16 questions MockDME has for this subject. The other 12 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.