A&P oral questions / General
Fundamentals of Electricity and Electronics: A&P oral exam questions
8 practice questions with answers for the Fundamentals of Electricity and Electronics subject (AM.I.A) of the FAA Aviation Mechanic General oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
Explain the difference between conventional current flow and electron flow.
What the examiner listens for
- Electron flow is from the negative terminal to the positive terminal
- Conventional flow is described as positive to negative
- Either works for troubleshooting if used consistentlybonus
A good answer: Conventional flow treats current as moving from positive to negative. Electron flow is what actually happens: electrons leave the negative side of the source and move toward the positive side.
Likely follow-up: Which of the two describes what the electrons actually do?
Reference: FAA-H-8083-30B Ch. 12, Conventional Flow and Electron Flow
What is the frequency of an alternating current, and what two things about a generator determine it?
What the examiner listens for
- Frequency is the number of cycles per secondbonus
- The number of poles in the generator
- The speed of rotation, in RPM
- It is measured in hertzbonus
A good answer: Frequency is the number of complete cycles per second, measured in hertz. In a generator it depends on the number of poles and the speed of rotation.
Likely follow-up: What frequency do most aircraft AC systems operate at?
Reference: FAA-H-8083-30B Ch. 12, Frequency Defined
How is a voltmeter connected, and what do you do if you are not sure how much voltage to expect?
What the examiner listens for
- In parallel with, or across, the component or source
- Start on the highest range and work down
- Observe correct polarity when measuring DCbonus
A good answer: A voltmeter is connected in parallel, across the component or source. If the voltage is unknown, take the first reading on the highest range and step down until you get a suitable reading, observing polarity.
Likely follow-up: Why should a voltmeter have high internal resistance?
Reference: FAA-H-8083-30B Ch. 12, Voltmeter Circuit Connections
What is the unit of electrical power, and how many of them equal one horsepower?
What the examiner listens for
- The watt
- 746 watts equal one horsepower
A good answer: Electrical power is measured in watts, and 746 watts equal one horsepower.
Likely follow-up: What happens to the electrical energy dissipated in a resistor?
Reference: FAA-H-8083-30B Ch. 12, Power in an Electrical Circuit
If a transformer steps the voltage up, what happens to the current, and why?
What the examiner listens for
- The current is stepped down by the same ratio
- Power out of the secondary cannot exceed power into the primarybonus
- The turns ratio determines whether it steps up or downbonus
A good answer: The current goes down by the same ratio that the voltage goes up. Power is volts times amps, and a transformer cannot put out more power than it takes in, so higher voltage means lower current.
Likely follow-up: What causes copper losses and eddy current losses in a transformer?
Reference: FAA-H-8083-30B Ch. 12, Transformers; Power in Transformers
What is a rheostat, and how is it connected in a circuit?
What the examiner listens for
- It is a variable resistor
- It is used to vary the amount of current in a circuit
- It is connected in series with the loadbonus
A good answer: A rheostat is a variable resistor used to vary the amount of current flowing in a circuit. It is connected in series with the load, for example for light dimming.
Likely follow-up: What is the other basic type of manually adjusted variable resistor?
Reference: FAA-H-8083-30B Ch. 12, Variable Resistors, Rheostat
How do you convert a binary number to decimal? Use binary one-zero-one as your example.
What the examiner listens for
- Add up the place values of the positions that contain a 1
- Place values are powers of two: 1, 2, 4, 8 and so onbonus
- Binary 101 equals decimal 5
A good answer: Each binary position has a place value that is a power of two: 1, 2, 4, 8 and so on from the right. Add the place values wherever there is a 1. For 101 that is 4 plus 1, which is 5.
Likely follow-up: What is decimal 8 written in binary?
Reference: FAA-H-8083-30B Ch. 3, Converting Binary Numbers to Decimal Numbers
You have to measure a voltage and you are not sure how high it is. How do you protect yourself and the meter?
What the examiner listens for
- Set the meter to the highest voltage range first, then work down
- Select the correct type of voltage, AC or DCbonus
- Observe correct polarity with the leadsbonus
A good answer: Select the right function, AC or DC, start on the highest voltage range so the meter is not pegged or damaged, then step down to a suitable range. Observe polarity and keep your hands off the probe tips.
Likely follow-up: Why can an ohmmeter not be used on a circuit that still has power applied?
Reference: FAA-H-8083-30B Ch. 12, Voltage Measurement
These are 8 of the 85 questions MockDME has for this subject. The other 77 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.