A&P oral questions / General
Fluid Lines and Fittings: A&P oral exam questions
8 practice questions with answers for the Fluid Lines and Fittings subject (AM.I.D) of the FAA Aviation Mechanic General oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
Where would you expect to find rigid metal tubing on an aircraft, and where is flexible hose used instead?
What the examiner listens for
- Rigid tubing is used in stationary applications with long, fairly straight runsbonus
- Flexible hose is used with moving parts or where there is considerable vibration
A good answer: Rigid tubing is used for stationary runs where long, relatively straight lines are possible. Flexible hose is used where the line connects to moving parts or is subject to considerable vibration.
Likely follow-up: Name some systems that commonly use rigid tubing.
Reference: FAA-H-8083-30B Ch. 9, Introduction
Can an AN flared fitting be interchanged with an MS flareless fitting, and how do you tell them apart?
What the examiner listens for
- No, they are not interchangeable
- The AN flared fitting has a cone at its end, or the MS flareless end is straight (either description)
- A flareless fitting uses a sleeve that grips the tube instead of a flarebonus
A good answer: No, AN flared and MS flareless fittings are not interchangeable. The AN flared fitting has a cone on the end that seats in the flare, while the MS flareless fitting has a straight end.
Likely follow-up: What color identifies an aluminum AN fitting, and what color a steel one?
Reference: FAA-H-8083-30B Ch. 9, AN Flared Fittings
What do the color-coded tapes or decals on an installed fluid line tell you?
What the examiner listens for
- Names at least one of: what the line contains, its function or system
- The primary hazard of the contentsbonus
- Markers use color codes, words, and geometric symbolsbonus
A good answer: The markers use color codes, words, and geometric symbols to identify each line's function, its contents, and its primary hazard, for example a fuel line marked FLAM.
Likely follow-up: Why is paint used instead of tape or tags to mark lines in an engine compartment?
Reference: FAA-H-8083-30B Ch. 9, Fluid Line Identification
Should you put sealing compound on the face of a flare or fitting to help it seal? Why or why not?
What the examiner listens for
- No, never apply compound to the flare or fitting faces
- The seal depends on metal-to-metal contact between flare and fitting
- Compound destroys that contactbonus
A good answer: No. A flared connection seals by metal-to-metal contact between the flare and the fitting cone, and compound on those faces destroys that contact.
Likely follow-up: If a properly torqued flared fitting still leaks, what should you do?
Reference: FAA-H-8083-30B Ch. 9, Rigid Tubing Installation and Inspection
Why is it important to use a torque wrench and the specified torque on a fluid line fitting?
What the examiner listens for
- It prevents overtightening
- It prevents undertightening
- Overtightening can damage or cut off the flare or ruin the sleeve or nutbonus
- Undertightening can let the line leak or blow out under pressurebonus
A good answer: Using a torque wrench and the prescribed value prevents both overtightening and undertightening. Too much torque can damage or cut off the flare and ruin the sleeve or nut; too little can let the line leak or blow out of the fitting under pressure.
Likely follow-up: A flare was formed badly and the joint weeps. Can extra torque fix it?
Reference: FAA-H-8083-30B Ch. 9, Rigid Tubing Installation and Inspection
What personal protective equipment do you use when handling hydraulic fluid or opening hydraulic lines?
What the examiner listens for
- Proper gloves
- Eye protection
- A respirator if phosphate ester mist or vapor exposure is possiblebonus
A good answer: I always use the proper gloves and eye protection when handling any type of hydraulic fluid, and if phosphate ester mist or vapor is possible, a respirator rated for organic vapors and mists.
Likely follow-up: What does prolonged skin contact with phosphate ester fluid do?
Reference: FAA-H-8083-31B Ch. 12, Health & Handling
What is the danger in taking apart a hydraulic accumulator, and what do you do first?
What the examiner listens for
- It contains a high-pressure air or nitrogen preloadbonus
- All preload pressure must be discharged before disassembly
- Failure to release it can cause serious injurybonus
A good answer: An accumulator holds a high-pressure air or nitrogen preload even when hydraulic pressure is off. Before disassembling it, I make sure all the preload has been discharged, because releasing it during disassembly can seriously injure the technician.
Likely follow-up: What should you know about the air valve before you discharge the preload?
Reference: FAA-H-8083-31B Ch. 12, Maintenance of Accumulators
A flareless fitting is weeping after installation. How far can you retighten it, and what is the risk of just adding more torque?
What the examiner listens for
- It may be tightened an additional one-sixth turn onlybonus
- Overtightening drives the sleeve into the tube and weakens it
- If it still leaks, remove and inspect the assemblybonus
A good answer: A leaking flareless connection may be tightened one more sixth of a turn, for a total of one-third turn. Beyond that the sleeve cuts too deeply and weakens the tube, so if it still leaks I take it apart and inspect for scores, cracks, or foreign material.
Likely follow-up: What could normal in-flight vibration do to a tube whose flareless nut was overtightened?
Reference: FAA-H-8083-30B Ch. 9, MS Flareless Fittings, installation
These are 8 of the 30 questions MockDME has for this subject. The other 22 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.