A&P oral questions / Powerplant

Engine Instrument Systems: A&P oral exam questions

4 practice questions with answers for the Engine Instrument Systems subject (AM.III.D) of the FAA Aviation Mechanic Powerplant oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.III.D.K1 · Knowledge · Fuel flow

In what units is fuel flow indicated on turbine aircraft, and why?

What the examiner listens for
  • Pounds per hour
  • Because fuel weight, not volume, is what matters on large turbine aircraftbonus
  • Light piston aircraft usually read gallons per hourbonus

A good answer: Turbine aircraft fuel flow is indicated in pounds per hour rather than gallons, because the weight of the fuel is a major factor for these aircraft. Light reciprocating aircraft normally read gallons per hour.

Likely follow-up: On a turbine engine, where is the fuel flow transmitter located and how does it sense flow?

Reference: FAA-H-8083-32B Ch. 10, Turbine Engine Instruments, Fuel-Flow Indicator

AM.III.D.K4 · Knowledge · Pressure (e.g., air, fuel, manifold, oil)

What kind of pressure does a manifold pressure gauge indicate, and what should it read with the engine shut down?

What the examiner listens for
  • Absolute pressure in the intake manifold, in inches of mercury
  • With the engine stopped it reads about the local atmospheric or barometric pressurebonus
  • About 30 inches at sea levelbonus

A good answer: A manifold pressure gauge reads absolute pressure in the intake manifold, in inches of mercury. With the engine not running it should read approximately the local barometric pressure, about thirty inches at sea level.

Likely follow-up: What would it suggest if the gauge read well below field barometric pressure with the engine stopped?

Reference: FAA-H-8083-32B Ch. 10, Manifold Pressure Indicator

AM.III.D.K7 · Knowledge · Engine pressure ratio (EPR)

What is engine pressure ratio, and what two pressures does it compare?

What the examiner listens for
  • An indication of thrust on a turbofan, used to set power
  • It compares turbine exhaust total pressure with engine inlet total pressure
  • Sensed by probes at the inlet, Pt2, and the turbine exhaust, Pt7bonus

A good answer: EPR is an indication of the thrust a turbofan is developing and is used to set takeoff power. It compares total pressure at the turbine exhaust, Pt7, with total pressure at the engine inlet, Pt2.

Likely follow-up: What could cause a false EPR reading on the ground in icing conditions?

Reference: FAA-H-8083-32B Ch. 10, Engine Pressure Ratio Indicator

AM.III.D.R1 · Risk management · Maintenance damage to the instrument or indicating system

While working around a cylinder head temperature or EGT system, why must you not shorten, splice, or substitute the thermocouple leads?

What the examiner listens for
  • The leads are made for a specific circuit resistance
  • Changing length, size, or material changes the resistance and makes the indication wrong
  • Leads must be the same metals as the thermocouple they connect tobonus

A good answer: Thermocouple leads are designed to give a specific resistance in the circuit. If their material, length, or cross-section is changed, the circuit resistance changes and the indicator reads incorrectly, so damaged leads are replaced with the correct part.

Likely follow-up: What would a high-resistance connection do to an EGT indication?

Reference: FAA-H-8083-31B Ch. 10, Thermocouple Temperature Indicators

These are 4 of the 17 questions MockDME has for this subject. The other 13 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects