A&P oral questions / Powerplant

Engine Fuel and Fuel Metering Systems: A&P oral exam questions

7 practice questions with answers for the Engine Fuel and Fuel Metering Systems subject (AM.III.I) of the FAA Aviation Mechanic Powerplant oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.III.I.K1 · Knowledge · Fuel/air ratio and fuel metering, and carburetor theory and operation

As an airplane with a carbureted engine climbs, what happens to the fuel-air mixture if nothing is adjusted, and why?

What the examiner listens for
  • The mixture becomes richer
  • Air density decreases with altitude, so less weight of air goes through the carburetor
  • The carburetor keeps metering about the same fuel for the same volume of airbonus
  • A mixture control, manual or automatic, is used to lean itbonus

A good answer: The mixture gets richer. Air density drops with altitude, so the engine takes in less weight of air, but the carburetor meters fuel by the volume of air through the venturi and keeps delivering about the same fuel. The mixture control is used to lean it.

Likely follow-up: Is the fuel-air ratio expressed by weight or by volume, and why?

Reference: FAA-H-8083-32B Ch. 2, Fuel Metering Devices for Reciprocating Engines

AM.III.I.K2 · Knowledge · Float carburetor theory, components, operation, and adjustment

What is the purpose of the accelerating pump in a float carburetor?

What the examiner listens for
  • It adds extra fuel when the throttle is opened quickly
  • Without it the mixture leans out momentarily on sudden throttle openingbonus
  • A lean stumble or slow acceleration would resultbonus

A good answer: When the throttle is opened quickly, airflow increases faster than the main metering system can respond and the mixture leans out for a moment. The accelerating pump, worked by the throttle linkage, sprays extra fuel into the venturi so the engine accelerates smoothly.

Likely follow-up: What happens to the accelerating pump's fuel if the throttle is opened slowly?

Reference: FAA-H-8083-32B Ch. 2, Accelerating System

AM.III.I.K5 · Knowledge · Digital engine control module (e.g., FADEC)

In a turbine engine FADEC fuel control, which unit decides how much fuel the engine gets, and which unit actually meters it?

What the examiner listens for
  • The electronic engine control computes the required fuel flow from sensor inputs
  • The fuel metering valve just follows the electronic control's commands
  • A true FADEC has no hydromechanical backupbonus

A good answer: The electronic engine control, the EEC, is the computing section: it takes the sensor information and determines the fuel flow. It sends that command to the fuel metering valve, which simply reacts and meters the fuel. A true FADEC has no hydromechanical backup.

Likely follow-up: How is redundancy provided in the EEC itself?

Reference: FAA-H-8083-32B Ch. 2, FADEC Fuel Control Systems

AM.III.I.K8 · Knowledge · Components, theory, and operation of turbine engine fuel metering system

What can happen in a turbine engine if the fuel control delivers too much fuel for the airflow? And too little?

What the examiner listens for
  • Too much: turbine overtemperature, compressor stall, or rich blowout (any one of these)
  • Rich blowout: too little oxygen to burn the excess fuel, which also cools the mixturebonus
  • Too little: lean flameout

A good answer: Too much fuel for the mass airflow can exceed the turbine blade temperature limit or cause a compressor stall and rich blowout. Too little fuel for the airflow causes a lean flameout. The fuel control has to schedule fuel to avoid both, especially during acceleration and deceleration.

Likely follow-up: Name some of the inputs a turbine fuel control senses to schedule fuel.

Reference: FAA-H-8083-32B Ch. 2, Turbine Engine Fuel System—General Requirements

AM.III.I.K12 · Knowledge · Fuel lines

What conditions would cause you to replace a flexible fuel hose during inspection?

What the examiner listens for
  • Deterioration such as separated plies or a hard, inflexible hose
  • Excessive cold flow, shown by deep clamp impressions or cracksbonus
  • The hose has collapsed at a bendbonus

A good answer: I would replace a hose if the plies have separated, if there is excessive cold flow such as permanent clamp impressions and cracks, if it has become hard and inflexible, or if it has collapsed at a bend or from misalignment.

Likely follow-up: You find a blister on the outer cover of a hose. How do you decide whether the hose is still serviceable?

Reference: FAA-H-8083-32B Ch. 2, Fuel System Inspection & Maintenance, Lines & Fittings

AM.III.I.K15 · Knowledge · Fuel filters

Why does a turbine fuel system micron filter need a bypass valve?

What the examiner listens for
  • Its very fine openings make it easy to clog
  • If it clogs, the bypass lets fuel keep flowing to the engine

A good answer: A micron filter has extremely small openings, so it filters very well but clogs easily with contamination or ice. The bypass valve is the safety feature that lets fuel continue to the engine if the element becomes blocked.

Likely follow-up: What damage can water do if it gets past the filter into the pump and fuel control?

Reference: FAA-H-8083-32B Ch. 2, Fuel Filters

AM.III.I.R2 · Risk management · Adjusting reciprocating engine fuel control systems

What can go wrong if idle mixture is adjusted on a cold engine or left too rich, and how do you avoid it?

What the examiner listens for
  • Adjust only with the engine warmed up and cylinder head temperature normal
  • An excessively rich idle mixture fouls spark plugsbonus
  • Clear the engine at higher rpm after each adjustmentbonus
  • Recheck the setting several times before releasebonus

A good answer: Idle mixture is always adjusted with the engine warmed up and cylinder head temperatures normal; otherwise the setting will be wrong. Too rich a setting causes incomplete combustion and spark plug fouling, too lean gives poor acceleration. I clear the engine at higher rpm after each adjustment and recheck the result several times.

Likely follow-up: After the idle mixture is correct, what adjustment do you make next?

Reference: FAA-H-8083-32B Ch. 2, Adjusting Idle Mixtures

These are 7 of the 27 questions MockDME has for this subject. The other 20 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects