A&P oral questions / Powerplant
Engine Fire Protection Systems: A&P oral exam questions
4 practice questions with answers for the Engine Fire Protection Systems subject (AM.III.E) of the FAA Aviation Mechanic Powerplant oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
What kind of material is burning in a Class B fire, and what is burning in a Class C fire?
What the examiner listens for
- Class B: flammable liquids such as fuel, oil, grease, or solvents
- Class C: energized electrical wiring or equipment
- Class A is ordinary combustibles like wood, cloth, or paperbonus
- Class D is flammable metal such as magnesiumbonus
A good answer: A Class B fire involves flammable petroleum products or other flammable liquids, greases, and solvents. A Class C fire involves energized electrical wiring and equipment.
Likely follow-up: What class is a magnesium fire, and why should you not use water or carbon dioxide on it?
Reference: FAA-H-8083-30B Ch. 1, Classification of Fires
On a dual-loop fire detection system, why must both loops normally signal before the crew gets a fire warning?
What the examiner listens for
- Requiring both loops, called AND logic, greatly reduces false fire warnings
- If one loop is inoperative, the system can be switched to single-loop operationbonus
- The remaining single loop still meets detection requirements, so the aircraft can be dispatchedbonus
A good answer: The two loops are connected with AND logic, so both must signal to give a warning. That greatly increases reliability against false fire warnings. If one loop fails, the system can operate on the other loop alone.
Likely follow-up: What happens if one loop fails its preflight test?
Reference: FAA-H-8083-32B Ch. 9, Dual-Loop Systems
What extinguishing agent is most common in fixed engine fire extinguishing systems, and why is it used?
What the examiner listens for
- Halon 1301
- Effective firefighting capability with relatively low toxicity
- Noncorrosive and needs no clean-up after dischargebonus
- It works by diluting the atmosphere with an agent that does not support combustionbonus
A good answer: Halon 1301. It is a very effective agent with relatively low toxicity, it is noncorrosive, and it needs no clean-up after discharge.
Likely follow-up: Why is only recycled Halon 1301 available today?
Reference: FAA-H-8083-32B Ch. 9, Fire Extinguishing Agents
Why should a discharge cartridge that was removed from one discharge valve not be installed in a different discharge valve?
What the examiner listens for
- The contact point protrudes a different distance in each valve
- The used cartridge may not make electrical contact, so there is no continuity
- Without continuity the bottle would not fire when neededbonus
A good answer: The distance the contact point protrudes varies from valve to valve. A cartridge already indented by a long contact point may not touch a shorter one, so there would be no continuity and the bottle would not discharge when commanded.
Likely follow-up: What is a discharge cartridge, in terms of the hazard it presents when you handle it?
Reference: FAA-H-8083-32B Ch. 9, Agent Containers
These are 4 of the 13 questions MockDME has for this subject. The other 9 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.