A&P oral questions / General
Cleaning and Corrosion Control: A&P oral exam questions
8 practice questions with answers for the Cleaning and Corrosion Control subject (AM.I.G) of the FAA Aviation Mechanic General oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
Why is keeping an aircraft clean considered part of maintenance and not just appearance?
What the examiner listens for
- Dirt and grease can hide cracks and other defects
- Dirt and grit on moving parts cause excessive wearbonus
- Salt water left on the aircraft corrodes exposed metalbonus
A good answer: A clean aircraft can be inspected accurately; dirt and grease can hide cracks. Grit also acts as a grinding compound on hinges and moving parts, and salt deposits cause corrosion.
Likely follow-up: What should you do about grease fittings and hinges after washing the aircraft?
Reference: FAA-H-8083-30B Ch. 8, Aircraft Cleaning
What does filiform corrosion look like, and where would you find it?
What the examiner listens for
- Worm-like or thread-like traces of corrosion
- Under the paint film on a coated metal surface
- Polyurethane finishes are especially susceptiblebonus
A good answer: Filiform corrosion shows up as fine worm-like traces of corrosion products underneath the paint film, and polyurethane finishes are especially prone to it.
Likely follow-up: If you leave filiform corrosion untreated, what can it turn into?
Reference: FAA-H-8083-30B Ch. 8, Filiform Corrosion
What are the general steps in a complete corrosion treatment?
What the examiner listens for
- Clean and strip the corroded areabonus
- Remove as much of the corrosion products as practicable
- Neutralize residual material in pits and crevicesbonus
- Restore the protective surface film and paint finish
A good answer: Clean and strip the area, remove as much of the corrosion products as practicable, neutralize what is left in pits and crevices, restore the protective surface film, and apply the coating or paint finish.
Likely follow-up: What do you do if the damage exceeds the manufacturer's limits?
Reference: FAA-H-8083-30B Ch. 8, Corrosion Removal
How does airless spray equipment atomize the coating, and what are its advantages and drawback?
What the examiner listens for
- A pump delivers the material to the gun under high hydraulic pressure
- It does not use compressed air to atomizebonus
- Less overspray and faster productionbonus
- Finish is not as fine as air-atomized spraybonus
A good answer: Airless equipment uses a pump to push the material through a small orifice at high hydraulic pressure, with no atomizing air. It gives less overspray and higher production, but not as fine a finish as air-atomized guns.
Likely follow-up: What does HVLP stand for, and why is the industry moving to it?
Reference: FAA-H-8083-31B Ch. 8, Spray Equipment (airless spraying)
What is Alclad, and how does it protect the structure?
What the examiner listens for
- A thin coating of relatively pure aluminum over the alloy core
- Pure aluminum is more corrosion resistant than the stronger alloy
- Avoid polishing or abrading the clad layer awaybonus
A good answer: Alclad is aluminum alloy sheet with a thin coating of relatively pure aluminum, which resists corrosion much better than the strong alloy underneath. You avoid removing that layer mechanically.
Likely follow-up: What is the most effective barrier overall between a metal surface and corrosive media?
Reference: FAA-H-8083-30B Ch. 8, Treatment of Unpainted Aluminum Surfaces
You see fisheyes forming as you spray. What usually causes them, and what do you do?
What the examiner listens for
- Surface contamination, usually silicone wax not cleaned off
- Stop spraying and clean off the wet paintbonus
- Clean the surface with a silicone wax remover before repaintingbonus
A good answer: Fisheyes are usually caused by silicone wax that was not cleaned off the surface. Stop spraying, wipe off the wet paint, clean thoroughly with a silicone wax remover, and start again.
Likely follow-up: What is the fix if the fisheyes are only found after the finish coat has set up?
Reference: FAA-H-8083-31B Ch. 8, Common Paint Troubles, Fisheyes
What usually causes sags and runs in a sprayed finish?
What the examiner listens for
- Too much paint applied to the area
- Gun held too close to the surfacebonus
- Gun moved too slowlybonus
- Paint thinned too muchbonus
A good answer: Sags and runs come from putting on too much paint: holding the gun too close, moving it too slowly, or over-thinning the paint.
Likely follow-up: How do you repair a run once it has dried?
Reference: FAA-H-8083-31B Ch. 8, Common Paint Troubles, Sags & Runs
Which abrasive papers should you avoid on aluminum or magnesium, and why?
What the examiner listens for
- Avoid silicon carbide (carborundum) paperbonus
- Avoid emery paper or crocus clothbonus
- Embedded abrasive or iron oxide particles cause corrosion
A good answer: Avoid silicon carbide paper, whose sharp grains bury themselves in the metal, and emery paper or crocus cloth, which leave iron oxide embedded in aluminum or magnesium and cause serious corrosion. Aluminum oxide paper is the safe choice.
Likely follow-up: What abrasive material is generally the first choice today for light corrosion removal?
Reference: FAA-H-8083-30B Ch. 8, Abrasive Papers
These are 8 of the 60 questions MockDME has for this subject. The other 52 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.