A&P oral questions / Airframe

Airframe Inspection: A&P oral exam questions

8 practice questions with answers for the Airframe Inspection subject (AM.II.D) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.II.D.K1 · Knowledge · Inspection requirements under 14 CFR part 91

How often does a typical Part 91 general aviation airplane need an annual inspection, and who can perform it?

What the examiner listens for
  • It must have had an annual inspection within the preceding 12 calendar months
  • It must be performed by a mechanic holding an inspection authorization, or another person authorized to perform annualsbonus
  • It must be approved for return to service afterwardbonus

A good answer: The aircraft may not be operated unless it has had an annual inspection within the preceding 12 calendar months and been approved for return to service. An annual has to be performed by a person authorized to do annuals, normally a mechanic holding an inspection authorization.

Likely follow-up: Name a type of aircraft the annual inspection requirement does not apply to.

Reference: 14 CFR 91.409(a)

AM.II.D.K1 · Knowledge · Inspection requirements under 14 CFR part 91

Can a 100-hour inspection be counted as the aircraft's annual inspection?

What the examiner listens for
  • Only if it is performed by a person authorized to perform annual inspections
  • And it is entered as an annual inspection in the maintenance records

A good answer: Not by itself. A 100-hour inspection can be substituted for an annual only if it is performed by a person authorized to perform annual inspections and it is entered as an annual inspection in the maintenance records.

Likely follow-up: Is there any difference in scope and detail between a 100-hour and an annual inspection?

Reference: 14 CFR 91.409(a)

AM.II.D.K3 · Knowledge · Requirements for complying with ADs

When you research ADs for an aircraft you are inspecting, which items do you have to search ADs for?

What the examiner listens for
  • The aircraft itself, by model and seriesbonus
  • The engine or engines
  • The propellerbonus
  • Any installed appliances

A good answer: Not just the airframe. I have to search for ADs on the aircraft, the engines, the propeller, and any installed appliance, by model and by specific series, and then compare them with the aircraft records.

Likely follow-up: How do you make the final determination that an AD applies to this particular aircraft?

Reference: FAA-H-8083-30B Ch. 2, Airworthiness Directives, Applicability and Compliance

AM.II.D.K5 · Knowledge · Special inspections

An aircraft has been struck by lightning. Which structure is most likely to be seriously damaged, and what do you look for?

What the examiner listens for
  • Non-metallic or composite structure without built-in bonding, such as a radome or fairingbonus
  • Look for burning, erosion, or other degradation of the material, especially composite resin
  • Check bonding straps and static discharge wicksbonus

A good answer: Metal structure usually shows little damage, but non-metallic parts such as a fiberglass radome, fairing, or unbonded composite can be burned. A visual inspection is required: I look for degradation, burning, or erosion of the composite resin, and I check the electrical bonding straps and static discharge wicks.

Likely follow-up: Why is damage to aluminum structure usually minimal after a lightning strike?

Reference: FAA-H-8083-30B Ch. 10, Special Inspections, Lightning Strike

AM.II.D.K8 · Knowledge · CFRs applicable to inspection and airworthiness

Which regulation sets the scope and detail of an annual or 100-hour inspection, and what does it require you to do before you start inspecting?

What the examiner listens for
  • Part 43 Appendix Dbonus
  • Remove or open all necessary inspection plates, access doors, fairings, and cowling
  • Thoroughly clean the aircraft and engine

A good answer: Appendix D to Part 43 sets the scope and detail. Before the inspection I must remove or open all necessary inspection plates, access doors, fairings, and cowling, and thoroughly clean the aircraft and engine.

Likely follow-up: Why would you look for leaks before you clean the area?

Reference: 14 CFR Part 43, Appendix D(a)

AM.II.D.K9 · Knowledge · Corrosion types and identification

What does filiform corrosion look like, and where does it form?

What the examiner listens for
  • Worm-like traces of corrosion products
  • It forms beneath the paint film on a coated metal surface
  • Polyurethane finishes are especially susceptiblebonus

A good answer: Filiform corrosion shows as characteristic worm-like traces of corrosion products under the paint film. It occurs on metal surfaces with an organic coating, and polyurethane finishes are especially susceptible.

Likely follow-up: Which metals does filiform corrosion usually attack?

Reference: FAA-H-8083-30B Ch. 8, Forms of Corrosion, Filiform Corrosion

AM.II.D.R2 · Risk management · Visual inspection and where to apply it

You look over a suspect fitting carefully and see no defects. Is it safe to conclude the part is good? Why or why not?

What the examiner listens for
  • Not necessarily; lack of visible defects does not mean further inspection is unnecessary
  • Defects may lie beneath the surfacebonus
  • Defects may be too small for the eye to detect, even with a magnifying glassbonus

A good answer: Not necessarily. The lack of visible defects does not mean further inspection is unnecessary, because some defects lie beneath the surface or are too small for the eye to see even with a magnifier. If the area is suspect, I follow up with another method such as penetrant or eddy current.

Likely follow-up: What simple aids improve a visual inspection?

Reference: FAA-H-8083-30B Ch. 10, Visual Inspection

AM.II.D.R4 · Risk management · Selection and use of checklists and other maintenance publications

What is the risk of doing an annual or 100-hour inspection from memory, and what does the regulation require instead?

What the examiner listens for
  • Items can be forgotten or overlookedbonus
  • A checklist must be used while performing the inspection
  • The checklist must include the scope and detail of Part 43 Appendix Dbonus

A good answer: Working from memory, items get forgotten or overlooked. The regulation requires a checklist to be used while performing an annual or 100-hour inspection. It can be my own, the manufacturer's, or from another source, but it must include the scope and detail of Appendix D to Part 43.

Likely follow-up: Is the manufacturer's checklist the only one you are allowed to use?

Reference: 14 CFR 43.15(c)(1)

These are 8 of the 30 questions MockDME has for this subject. The other 22 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects