A&P oral questions / General

Aircraft Materials, Hardware, and Processes: A&P oral exam questions

8 practice questions with answers for the Aircraft Materials, Hardware, and Processes subject (AM.I.E) of the FAA Aviation Mechanic General oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.I.E.K1 · Knowledge · Materials commonly used in aircraft and their general application

Why are ductile metals such as aluminum alloys preferred for aircraft skins and formed parts?

What the examiner listens for
  • Ductile metal can be bent or formed into shape without breaking, so it is easy to form
  • They resist failure under shock loadsbonus

A good answer: Ductility lets a metal be permanently drawn, bent, or twisted into shape without breaking. Ductile metals are preferred because they are easy to form and resist failure under shock loads, which is why aluminum alloys are used for skins, ribs, spars, and bulkheads.

Likely follow-up: What is the opposite property, and why is it undesirable in structure?

Reference: FAA-H-8083-30B Ch. 7, Properties of Metals, Ductility

AM.I.E.K2 · Knowledge · Heat treatment and metal working processes

When solution heat-treating aluminum alloy such as 2024, why must the part go from the furnace into the quench with minimum delay?

What the examiner listens for
  • Names at least one of: alloying elements re-precipitate during the delay, reduced resistance to intergranular corrosion
  • Precipitation occurs along the grain boundariesbonus
  • Formability is also poorerbonus

A good answer: If the metal cools slightly before the quench, the alloying constituents begin to re-precipitate along the grain boundaries. That hurts formability and, on alloys like 2017, 2024, and 7075, lowers the resistance to intergranular corrosion.

Likely follow-up: What is case hardening and what kind of part is it used for?

Reference: FAA-H-8083-30B Ch. 7, Heat-Treatment of Nonferrous Metals, Lag Between Soaking & Quenching

AM.I.E.K4 · Knowledge · Hardware commonly used in aircraft (e.g., bolts, nuts, screws, pins, washers, turnlock fasteners, cables, cable fittings, and rigid line couplings)

What is a turnbuckle used for in a control cable system, and how can it adjust in both directions?

What the examiner listens for
  • It makes minor adjustments in cable length and adjusts cable tension
  • One terminal has right-hand threads and the other has left-hand threadsbonus

A good answer: A turnbuckle is used to make small adjustments in cable length and to set cable tension. It has one right-hand threaded terminal and one left-hand threaded terminal, so turning the barrel draws both in or lets both out.

Likely follow-up: After adjustment, how many threads may be exposed outside the turnbuckle barrel?

Reference: FAA-H-8083-30B Ch. 7, Turnbuckles

AM.I.E.K5 · Knowledge · Safety wire and safety clip requirements and techniques

How should the prongs of a cotter pin be finished when it is installed through a castellated nut?

What the examiner listens for
  • Names at least one of: upper prong does not extend beyond the bolt diameter, lower prong does not rest on the washer
  • Prongs are trimmed if they are too longbonus
  • Prongs are bent over a reasonable radius, not a sharp anglebonus

A good answer: The prong bent up over the end of the bolt must not extend past the bolt diameter, and the prong bent down must not rest against the washer; trim them if necessary. Bends should be made over a reasonable radius because sharp bends invite breakage.

Likely follow-up: Can a cotter pin be reused after it is removed?

Reference: FAA-H-8083-30B Ch. 7, Cotter Pin Safetying

AM.I.E.K8 · Knowledge · Torquing tools, principles, and procedures

Describe the correct way to pull a click-type torque wrench, and what happens if you jerk it.

What the examiner listens for
  • Pull with a smooth, steady motion
  • A fast or jerky pull results in an improperly torqued fastener
  • Stop when the handle releases, or breaksbonus

A good answer: You set the wrench, then pull with a smooth, steady motion until the handle releases or breaks. A fast or jerky pull gives an improperly torqued fastener.

Likely follow-up: If the torque chatters or jerks during the final pull, what should you do?

Reference: FAA-H-8083-30B Ch. 7, Torque Wrenches

AM.I.E.K10 · Knowledge · Relationship between torque and fastener preload

Why does the standard torque table assume dry threads, and when are you allowed to lubricate them?

What the examiner listens for
  • Threads are clean and dry unless the manufacturer specifies otherwise
  • Lubrication changes thread friction, so the same wrench torque gives a different bolt tensionbonus
  • Lubricate only where specifically instructed, for example corrosion-resistant steel partsbonus

A good answer: Standard torque values are for clean, dry threads. Lubricant lowers the friction, so the same wrench reading would stretch the bolt more than intended, which is why you lubricate only when the instructions specifically call for it.

Likely follow-up: What can overtorquing do to a bolt that might require a check before it is reused?

Reference: AC 43.13-1B, para 7-40

AM.I.E.K12 · Knowledge · Characteristics of acceptable welds

Besides bead appearance, what does an acceptable weld show regarding penetration and the surrounding base metal?

What the examiner listens for
  • Penetration deep enough to ensure fusion of base metal and filler rod
  • Base metal shows no pitting, burning, cracking, or distortion

A good answer: The depth of penetration must be enough to ensure fusion of the base metal and the filler rod, and the base metal next to the weld should show no pitting, burning, cracking, or distortion.

Likely follow-up: How should welding scale be removed before inspection?

Reference: AC 43.13-1B, para 4-78, Inspection of a Completed Weld

AM.I.E.R2 · Risk management · Improper torque

What are the consequences of undertorquing and of overtorquing a bolt?

What the examiner listens for
  • Undertorque lets the joint loosen or move, causing wear of the fastener and the parts it secures
  • Overtorque overstresses the bolt, nut, or threads and can cause failure

A good answer: An undertorqued fastener lets the joint move, causing unnecessary wear of the nut, bolt, and the parts they hold. Overtorque overstresses the threaded area and can cause the bolt or nut to fail.

Likely follow-up: What is the benefit to the structure of using the proper torque?

Reference: AC 43.13-1B, para 7-40

These are 8 of the 53 questions MockDME has for this subject. The other 45 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects