A&P oral questions / Airframe

Aircraft Instrument Systems: A&P oral exam questions

8 practice questions with answers for the Aircraft Instrument Systems subject (AM.II.H) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.

AM.II.H.K1 · Knowledge · Annunciator indicating systems and the meaning of warning, caution, and advisory lights

On an annunciator panel, what is the difference in meaning between a red light and a yellow or amber light?

What the examiner listens for
  • Red means an unsatisfactory condition that needs immediate attention or action
  • Yellow or amber is a caution: a condition that needs monitoring
  • Green indicates a satisfactory conditionbonus

A good answer: Red is a warning: an unsatisfactory condition that needs immediate attention or action. Yellow or amber is a caution, a serious condition that needs further monitoring. Green shows a satisfactory condition.

Likely follow-up: How can the crew or a mechanic confirm that all the annunciator bulbs and warning circuits are working?

Reference: FAA-H-8083-31B Ch. 10, Annunciator Panels

AM.II.H.K3 · Knowledge · Magnetic compass swinging procedures

How should the aircraft be configured while you swing the compass on a compass rose?

What the examiner listens for
  • Normal equipment on board and turned on, engine running, to simulate flight conditions
  • Aircraft in level flight attitudebonus
  • Kept clear of ferrous vehicles, equipment, and loose magnetic items in the cabinbonus

A good answer: The aircraft is set up to simulate flight: level flight attitude, all normal equipment on board and switched on, and the engine running. The compass rose area and the cabin are kept free of ferrous objects that could disturb the compass.

Likely follow-up: What kind of screwdriver do you use on the compensating screws, and why?

Reference: FAA-H-8083-31B Ch. 10, Magnetic Compass Maintenance & Compensation

AM.II.H.K6 · Knowledge · Position indication sensors and instruments

How does a synchro-type remote-indicating system, such as a DC selsyn, show the position of the flaps on a flight deck indicator?

What the examiner listens for
  • A transmitter mechanically linked to the moving unit sends electrical signals to the flight deck indicator
  • The indicator pointer follows, mirroring the position of the transmitterbonus
  • DC selsyn is used on DC aircraft; autosyn or magnesyn on AC aircraftbonus

A good answer: A transmitter is mechanically linked to the flap, and as the flap moves the transmitter changes the electrical signals sent over wires to the indicator, whose pointer follows. DC aircraft commonly use a selsyn system; AC aircraft use autosyn or magnesyn.

Likely follow-up: In a DC selsyn landing gear indicator, how does the indicator show that the gear is actually locked?

Reference: FAA-H-8083-31B Ch. 10, Remote Sensing & Indication, Synchro-Type Remote-Indicating Instruments

AM.II.H.K10 · Knowledge · Pitot-static system

Describe the basic static system leak test on an unpressurized airplane. What do you apply, how long do you wait, and what leakage is acceptable?

What the examiner listens for
  • Apply suction at the static port until the altimeter shows about 1,000 feet above the starting reading
  • Seal the system and watch for 1 minutebonus
  • The altimeter must not lose more than 100 feet

A good answer: A tester is connected at the static vent and pressure is reduced until the altimeter indicates 1,000 feet higher. The system is sealed and observed for one minute, and a loss of more than 100 feet of indicated altitude is not acceptable.

Likely follow-up: If it fails, where are leaks most likely to be found?

Reference: FAA-H-8083-31B Ch. 10, Pitot-Static System Maintenance & Tests

AM.II.H.K15 · Knowledge · Built-in test equipment

What is built-in test equipment, or BITE, and how does it help you as a mechanic?

What the examiner listens for
  • The system monitors and tests itself for faults
  • It reports or stores fault information that maintenance can retrieve
  • It can trace a fault to a specific line replaceable unitbonus

A good answer: BITE is built-in test equipment: the system monitors and tests itself as well as the aircraft systems connected to it. It stores and displays fault messages that maintenance can retrieve, often pointing to the line replaceable unit at fault, which speeds up troubleshooting.

Likely follow-up: When using BITE fault data, whose procedures do you follow?

Reference: FAA-H-8083-31B Ch. 10, ECAM; Flight Management System (FMS)

AM.II.H.K19 · Knowledge · 14 CFR parts 43 and 91 requirements for static system leak checks

Which of the 91.411 tests may a certificated mechanic with an airframe rating perform, and who has to do the rest?

What the examiner listens for
  • An airframe-rated mechanic may do the static pressure system tests and inspections only
  • Altimeter tests must be done by the manufacturer or an appropriately rated repair stationbonus

A good answer: A mechanic with an airframe rating may perform only the static pressure system test and inspection. The altimeter and altitude reporting equipment tests have to be done by the aircraft manufacturer or a properly equipped and rated repair station.

Likely follow-up: Does comparing the aircraft altimeter with the altimeter built into your leak tester satisfy the altimeter test requirement?

Reference: 14 CFR 91.411(b)

AM.II.H.K22 · Knowledge · Takeoff and landing gear configuration warning systems

What conditions cause the landing gear aural warning to sound on an airplane with retractable gear?

What the examiner listens for
  • The throttle is retarded
  • The landing gear is not down and locked

A good answer: The gear warning sounds when the throttle is retarded, as for landing, while the landing gear is not down and locked.

Likely follow-up: On a transport airplane, what other input besides throttle position is often part of the gear warning logic?

Reference: FAA-H-8083-31B Ch. 10, Aural Warning Systems

AM.II.H.R1 · Risk management · Use of pressurized air and water during maintenance or cleaning of aircraft instrument systems

Why is water in a pitot-static system a hazard, for example after washing the aircraft or heavy rain?

What the examiner listens for
  • It can cause inaccurate or intermittent flight instrument indications
  • It is worse if the water freezes in flightbonus
  • Drain the system at its low-point drainsbonus

A good answer: Water trapped in the lines can cause inaccurate or intermittent airspeed, altimeter, and vertical speed indications, and it is especially dangerous if it freezes in flight. The system should be drained at its low-point drains, and the ports kept protected from water.

Likely follow-up: How would you keep water out of the static ports while the aircraft is being washed, and what must you remember afterward?

Reference: FAA-H-8083-31B Ch. 10, Pitot-Static System Maintenance & Tests

These are 8 of the 42 questions MockDME has for this subject. The other 34 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.

Get the app when it launches

MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.

We use your address only for this one launch email and delete it afterwards. Privacy policy.

Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.

All 40 subjects