A&P oral questions / Airframe
Aircraft Fuel Systems: A&P oral exam questions
8 practice questions with answers for the Aircraft Fuel Systems subject (AM.II.J) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
How does a gravity feed fuel system work, and what kind of airplane typically has one?
What the examiner listens for
- The tanks are above the engine, so gravity delivers the fuel
- Typical of high-wing aircraft with a tank in each wingbonus
- No fuel pump is neededbonus
A good answer: On a high-wing airplane the wing tanks sit above the engine, so gravity alone delivers the fuel through the selector valve and strainer to the carburetor. With no pump, it is the simplest fuel system.
Likely follow-up: Why are the two tanks in a gravity feed system vented to each other?
Reference: FAA-H-8083-31B Ch. 14, Gravity Feed Systems
What are the three types of aircraft fuel tanks?
What the examiner listens for
- Rigid removable tanks
- Bladder tanks
- Integral fuel tanks
A good answer: The three types are rigid removable tanks, bladder tanks, also called fuel cells, and integral tanks, where sealed aircraft structure forms the tank.
Likely follow-up: What is a wet wing?
Reference: FAA-H-8083-31B Ch. 14, Fuel Tanks
On a fuel-injected engine that uses a pressure gauge as the fuel flow indicator, what does a clogged injector do to the reading?
What the examiner listens for
- The gauge reads higher, as if fuel flow had increased
- Actual fuel flow is reducedbonus
- Check the reading against exhaust gas temperaturebonus
A good answer: A clogged injector reduces actual fuel flow, but the restriction raises the pressure, so the gauge shows a higher fuel flow. The indication should be compared with EGT to tell what is really happening.
Likely follow-up: Why does fuel pressure normally work as a measure of flow on these engines?
Reference: FAA-H-8083-31B Ch. 14, Fuel Flow Meters
Before pressure fueling or defueling an aircraft you are not familiar with, what do you need to confirm about the order in which tanks are filled or emptied?
What the examiner listens for
- There may be a prescribed tank sequence
- The wrong sequence can cause structural damage
- Confirm the procedure in the manufacturer's manualbonus
A good answer: Tanks may have to be fueled or defueled in a prescribed sequence to prevent structural damage to the airframe. Confirm the proper procedure in the manufacturer's manual before starting.
Likely follow-up: What else must be correct about the refueling pump before you start pumping?
Reference: FAA-H-8083-31B Ch. 14, Fueling & Defueling Procedures
How do the physical characteristics of jet fuel compare with aviation gasoline?
What the examiner listens for
- Names at least one of: jet fuel is less volatile, more viscous, or has a higher boiling point
- Jet fuel is a kerosene-type fuelbonus
- Jet fuel holds more water and supports microbial growthbonus
A good answer: Turbine fuel is a kerosene-type fuel with higher viscosity, much lower volatility and a higher boiling point than gasoline. Because it is more viscous it holds water and particles longer, so microbes are more of a problem.
Likely follow-up: May jet fuel and AVGAS ever be mixed or substituted for each other?
Reference: FAA-H-8083-31B Ch. 14, Turbine Engine Fuels
How does a capacitance-type fuel quantity system sense how much fuel is in the tank?
What the examiner listens for
- Tank probes act as capacitors
- Capacitance changes with fuel level because fuel and air have different dielectric values
- The probes have no moving partsbonus
A good answer: Each tank probe is a capacitor with two concentric plates. The material between the plates is fuel, air, or a mix depending on the level, so the dielectric, and therefore the capacitance, changes with fuel quantity. A bridge circuit converts that to an indication.
Likely follow-up: In what units is a capacitance system usually calibrated, and why?
Reference: FAA-H-8083-31B Ch. 14, Fuel Quantity Indicating Systems
What is the most common fuel contaminant, and what routine practice removes it?
What the examiner listens for
- Water
- Draining the sumps and strainers, daily or before flight
- It settles to the low points because it is heavier than fuelbonus
A good answer: Water is the most common contaminant. It settles to the tank sumps and strainers, so draining the sumps and strainers daily, combined with periodic filter changes and inspections, is the routine control.
Likely follow-up: Why is sump draining alone not enough on turbine aircraft?
Reference: FAA-H-8083-31B Ch. 14, Checking for Fuel System Contaminants
Fuel is spilled on the ramp during servicing. How do you handle a small spill and a large spill?
What the examiner listens for
- Wipe up small spills immediately
- Flood larger spills with water to dissipate the fuelbonus
- Do not sweep spilled fuelbonus
A good answer: Spilled fuel vaporizes quickly and is a fire hazard. Wipe up small spills immediately; larger spills can be flooded with water to dissipate the fuel. Never sweep spilled fuel on the ramp.
Likely follow-up: Why should a fuel spill not be swept?
Reference: FAA-H-8083-31B Ch. 14, Fire Hazards When Fueling or Defueling
These are 8 of the 34 questions MockDME has for this subject. The other 26 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.