A&P oral questions / Airframe
Aircraft Electrical Systems: A&P oral exam questions
8 practice questions with answers for the Aircraft Electrical Systems subject (AM.II.K) of the FAA Aviation Mechanic Airframe oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
Engine speed and electrical load keep changing in flight. How is the output of a DC generator kept under control?
What the examiner listens for
- By controlling the current in the generator field
- More field current gives more output, less field current gives lessbonus
- A voltage regulator or generator control unit does this automaticallybonus
A good answer: Generator output is controlled by varying the field current, which changes the strength of the magnetic field. More field current means more output and less means less. On the aircraft a voltage regulator or generator control unit does this automatically.
Likely follow-up: If the regulator senses that system voltage is too high, what does it do to the field current?
Reference: FAA-H-8083-31B Ch. 9, Generator Controls
What is a starter-generator, and why is it used on many turbine-powered aircraft?
What the examiner listens for
- One unit that works as both the engine starter and the generator
- Combining two units in one housing saves space and weight
- It acts as a motor for starting, then is switched to generate powerbonus
A good answer: A starter-generator is a single unit that acts as a motor to start the engine and then as a generator once the engine is running. Putting both functions in one housing saves space and weight.
Likely follow-up: What does the generator control unit change inside the unit when it switches from starting to generating?
Reference: FAA-H-8083-31B Ch. 9, Generator Controls for High-Output Generators
Aircraft wire is sized by American wire gauge. What happens to the wire diameter as the gauge number gets larger?
What the examiner listens for
- The wire diameter gets smaller as the gauge number gets larger
- A smaller wire carries less currentbonus
A good answer: In the American wire gauge system the diameter gets smaller as the gauge number gets larger, so a number 20 wire is much smaller than a number 4 wire and carries less current.
Likely follow-up: How could you find the size of a wire that has no marking on it?
Reference: FAA-H-8083-31B Ch. 9, Wire Size Selection
Why are bonding jumpers installed across the hinges of control surfaces as part of lightning protection?
What the examiner listens for
- They carry lightning current across the hinge so the hinge itself is not burned
- The jumper is a low-impedance path from the surface to the structurebonus
- Burned hinges could mean loss of controlbonus
A good answer: The jumper gives lightning current a low-impedance path across the hinge into the airframe. Without it the current would pass through the hinge itself and could burn it, possibly causing loss of control.
Likely follow-up: Why should sharp bends and loops be avoided in those jumpers?
Reference: AC 43.13-1B, para 11-193
You find a tripped circuit breaker during an inspection. What should happen before that breaker is reset?
What the examiner listens for
- The circuit should be checkedbonus
- The fault should be found and removed before resetting
- If it trips again after one reset, troubleshoot before resetting againbonus
A good answer: A tripped breaker means something is wrong, so the circuit should be checked and the fault removed before the breaker is reset. If a breaker is reset once and trips again, there is a circuit fault and it must be troubleshot before any further reset.
Likely follow-up: What does it mean when a circuit breaker is described as trip-free?
Reference: FAA-H-8083-31B Ch. 9, Circuit Breakers
Two electrical connectors are mounted side by side. How is the installation designed so they cannot be plugged into the wrong receptacle?
What the examiner listens for
- Adjacent connectors are made physically different, for example in shell size, coupling, insert arrangement, or keying
- Otherwise wires are routed and clamped so the wrong pair cannot reach each otherbonus
- Markings or color stripes alone are not relied onbonus
A good answer: Adjacent connectors are made physically different: a different shell size, coupling method, insert arrangement, or keying. If that is not practical, the wiring is routed and clamped so the wrong halves cannot reach. Color coding or markings alone are not relied on because they deteriorate.
Likely follow-up: What do you do with unused contact cavities in a connector?
Reference: FAA-H-8083-31B Ch. 9, Adjacent Locations
When you measure current with an ammeter during troubleshooting, what connection mistake can destroy the meter, and how should it be connected instead?
What the examiner listens for
- Never connect it across a voltage source such as a battery or generator
- Connect the ammeter in series with the load being measuredbonus
- Its very low resistance would let a very high current flow through the meterbonus
- Start on the highest range if the current is unknownbonus
A good answer: An ammeter must never be connected across a source of voltage, in parallel, because its resistance is extremely low and a very high current would flow through it and damage it. It is always connected in series with the component whose current is being measured.
Likely follow-up: What precaution applies before you measure resistance of a component with an ohmmeter?
Reference: FAA-H-8083-30B Ch. 12, The Ammeter
A wire bundle slopes down toward a connector. What is the hazard, and what do you do about it when routing the bundle?
What the examiner listens for
- Fluid or condensation can run along the wires into the connector
- Provide a drip loop so the wires go down and then up to the connector
- If a drip loop is not possible, seal the entrancebonus
A good answer: Moisture and fluids will run down the wires into the connector and cause corrosion or shorts. The fix is a drip loop: the wires dip below the connector and come back up to it, so fluid collects at the bottom of the loop and drips off or evaporates.
Likely follow-up: How far apart, at most, should the clamps supporting a wire bundle be spaced?
Reference: FAA-H-8083-31B Ch. 9, Protection Against Solvents & Fluids
These are 8 of the 38 questions MockDME has for this subject. The other 30 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.