A&P oral questions / General
Aircraft Drawings: A&P oral exam questions
6 practice questions with answers for the Aircraft Drawings subject (AM.I.B) of the FAA Aviation Mechanic General oral exam. Say your answer out loud first, the way you will in front of the DME, then open the answer and check which points you covered.
What does a schematic diagram of an aircraft system show you, and what does it not show?
What the examiner listens for
- Shows how components relate to each other within the system
- Names at least one thing it does not show: physical location of components in the aircraft, or their actual size and shape
- Used mainly for troubleshooting and understanding system operationbonus
A good answer: A schematic shows the components in relation to each other within the system and how the system operates. It does not show where the components are physically located in the aircraft or their actual size and shape, which is why it is mainly a troubleshooting tool.
Likely follow-up: Which kind of diagram would you use to find where a component is physically located in the aircraft?
Reference: FAA-H-8083-30B Ch. 4, Schematic Diagrams
What is a sectional view on a drawing, and why would the draftsman include one?
What the examiner listens for
- Part of the object is shown cut away at a cutting plane
- It shows internal shape or construction that exterior views cannot show clearly
- The cut surfaces are marked with section lines, or crosshatchingbonus
A good answer: A sectional view shows the object as if part of it were cut away at a cutting plane. It is used to show the interior shape and construction that cannot be shown clearly in an exterior view.
Likely follow-up: What is the difference between a full section and a half section?
Reference: FAA-H-8083-30B Ch. 4, Sectional View Drawings
You have to sketch a repair so that someone else can make the repair or fabricate the part. What must that sketch contain?
What the examiner listens for
- All the information needed by the person making the repair or the part
- Necessary construction details such as dimensions if a part is manufactured from itbonus
- Notes, title, and datebonus
A good answer: A repair sketch has to give all the information necessary for the person who makes the repair or manufactures the part, which means all needed views, dimensions, and construction details, not just a picture of the object.
Likely follow-up: When is it acceptable for a sketch to have no dimensions at all?
Reference: FAA-H-8083-30B Ch. 4, Repair Sketches
A drawing calls out a location as fuselage station 185. What does that mean?
What the examiner listens for
- The location is 185 inches from the datum
- The datum is a reference point chosen by the manufacturer, often the nose or zero stationbonus
A good answer: Fuselage station 185 is a point 185 inches from the aircraft's datum, measured along the length of the fuselage. The datum is usually the nose or zero station but can be another point chosen by the manufacturer.
Likely follow-up: How are locations to the left or right of the centerline identified?
Reference: FAA-H-8083-30B Ch. 4, Station Numbers & Location Identification on Aircraft
You need to check a dimension, but there is no tolerance shown next to it on the drawing. What tolerance applies?
What the examiner listens for
- The general print tolerance applies
- The print tolerance is usually found in the title blockbonus
A good answer: When no tolerance is shown on the dimension line, the general print tolerance applies, and that is normally given in the title block. I would not assume the dimension has no limits or make up my own.
Likely follow-up: What kind of dimensions is a general print tolerance meant for?
Reference: FAA-H-8083-30B Ch. 4, Reading and Interpreting Drawings
You pull a drawing to do a job. Before you read the illustration itself, what do you check to be sure it is the right drawing for this aircraft?
What the examiner listens for
- The drawing number and description of the articlebonus
- The model affected, so it applies to this aircraft
- The latest change letter, or revision
- The next assembly listedbonus
A good answer: First I read the drawing number and the description, then I check the model affected, the latest change letter, and the next assembly. Only after confirming that the drawing applies to this aircraft and is the current change do I go on to read it.
Likely follow-up: What could happen if you worked from a drawing that applies to a different model or serial range?
Reference: FAA-H-8083-30B Ch. 4, Reading and Interpreting Drawings
These are 6 of the 23 questions MockDME has for this subject. The other 17 are in the app, where the examiner voice asks, you answer by voice, and your answer is graded point by point.
Get the app when it launches
MockDME for iPhone asks these questions out loud, listens to your spoken answer, and tells you which points you covered and which you missed. One email on launch day, nothing else.
We use your address only for this one launch email and delete it afterwards. Privacy policy.
Practice questions written from the Aviation Mechanic Airman Certification Standards (FAA-S-ACS-1) and the FAA handbooks cited under each answer. They are not the examiner's actual questions: your DME picks those. Found an error? Tell us and we will fix it.